Jindal Medi Surge

LOCKING RE-CONSTRUCTION PLATE 2.0MM STRAIGHT THICKNESS ORTHOPEDIC IMPLANT The aim of any surgical fracture treatment is to reconstruct the anatomy and restore its function. Internal fixation is distinguished by precise reduction, stable fixation preservation of blood supply, and early functional mobilization. Locking Plate and screw osteosynthesis have been established and clinically recognized for quite some time. Clinical results have been improved by using (internal fixation) in metaphyseal fractures and in osteopenic bone. Jindal Medi Surge Orthopedic Small Fragment Locking compression plate system is part of medical grade stainless steel and titanium plate and screw system that merges locking head screw technology with conventional plating techniques. The Small Locking Compression Plate System has many similarities to existing non-locking plate systems but with a few important improvements. Instead of cortical screws, locking head screws provide the ability to create a fixed-angle construct which also provides advantages in osteopenic bone or multifragmentary fractures where traditional screw purchase is compromised. Locking head screws does not rely on plate/bone compression to maintain stability, but function similarly to multiple small angled blade plates. The Small Locking Compression Plate System has the following features: Uniform hole spacing, Load (compression) and neutral screw positions, Small Locking Compression Plates have combination locking and compression holes (combi holes), The combi holes allow placement of standard cortical and cancellous bone screws on one side or threaded conical locking screws on the opposite side of each hole. Threaded hole section for locking screw. Dynamic compression unit hole section for standard screw. Locking screw in the threaded side of the plate hole. Indications: All Small Fragment LCP Locking Compression Plates are intended for fixation of fractures, osteotomies, and non-union of the clavicle, scapula, olecranon, humerus, radius, ulna, pelvis, distal tibia and fibula, particularly in osteopenic bone. Fixation Principles: The following points distinguish treatment using locking head screw technology from conventional plating techniques: It enables fracture treatment using compression plating with conventional cortical or cancellous screws. A locking compression plate can be used as an internal fixator and permit stable bridging over shattered zones. The small locking compression plate system permits the combination of conventional and locking screws. Unicortical locking screw permits better vascularity.

Locking Periarticular Proximal Humerus Plate 3.5mm (Left & Right) Orthopedic Implant With locked plating, the use of locking screws provides locking compression, which is especially useful in fractures prone to collapse. The locking humeral plate was designed for humeral fractures whereby it is contoured to the anatomy of the lateral aspect of the proximal humeral metaphysis and proximal diaphysis. Fragments must be reduced before locking screws are placed. The plate may be used to aid reduction and non-locked screws may be used to achieve interfragmentary compression. All Jindal Medi Surge Orthopedic Locking Humerus Bone Plates are made from medical grade stainless steel & titanium only.

Locking Posterior Medial Tibia Plate 3.5mm Orthopedic Implant Jindal Medi Surge Orthopedic Locking Tibia Bone Plates have a limited-contact profile. The head and neck portions of the plates accept locking screws. The screw hole pattern allows a raft of subchondral locking screws to buttress and maintain reduction of the articular surface. This provides resistance to local depression loads in addition to the stability of the fixed angle construct created by locking the screws into the plate. The LPS Proximal Tibia Plate — Low Bend is part of the locking plate system (LPS), which merges locking screw technology with conventional plating techniques. The locking plate system (LPS) here has Combi-holes in the plate shaft. The Combi-hole provides flexibility of axial compression and locking capability throughout the length of the plate shaft. Indication for fractures of the proximal tibia, including: simple, comminuted, lateral wedge, depression, medial wedge, bicondylar combination of lateral wedge and depression, periprosthetic, and fractures with associated shaft fractures. The plates can also be used for treatment of nonunions, malunions, and osteopenic bone. All plates are made from medical grade stainless steel & titanium alloy.

PHMA Locking Plate 3.5mm (Proximal Humeral Multi Angle) Short SS Orthopedic Implant With locked plating, the use of locking screws provides locking compression, which is especially useful in fractures prone to collapse. The locking humeral plate was designed for humeral fractures whereby it is contoured to the anatomy of the lateral aspect of the proximal humeral metaphysis and proximal diaphysis. Fragments must be reduced before locking screws are placed. The plate may be used to aid reduction and non-locked screws may be used to achieve interfragmentary compression. All Jindal Medi Surge Orthopedic Locking Humerus Bone Plates are made from medical grade stainless steel & titanium only.

LOCKING POSTERIOR MEDIALTIBIA PLATE 3.5MM ORTHOPEDIC IMPLANT Jindal Medi Surge Orthopedic Locking Tibia Bone Plates have a limited-contact profile. The head and neck portions of the plates accept locking screws. The screw hole pattern allows a raft of subchondral locking screws to buttress and maintain reduction of the articular surface. This provides resistance to local depression loads in addition to the stability of the fixed angle construct created by locking the screws into the plate. The LPS Proximal Tibia Plate — Low Bend is part of the locking plate system (LPS), which merges locking screw technology with conventional plating techniques. The locking plate system (LPS) here has Combi-holes in the plate shaft. The Combi-hole provides flexibility of axial compression and locking capability throughout the length of the plate shaft. Indication for fractures of the proximal tibia, including: simple, comminuted, lateral wedge, depression, medial wedge, bicondylar combination of lateral wedge and depression, periprosthetic, and fractures with associated shaft fractures. The plates can also be used for treatment of nonunions, malunions, and osteopenic bone. All plates are made from medical grade stainless steel & titanium alloy.

LOCKING PROXIMAL FEMUR PLATE 5.0/7.0MM ORTHOPEDIC IMPLANT Jindal Medi Surge Orthopedic Locking Tibia Bone Plates have a limited-contact profile. The head and neck portions of the plates accept locking screws. The screw hole pattern allows a raft of subchondral locking screws to buttress and maintain reduction of the articular surface. This provides resistance to local depression loads in addition to the stability of the fixed angle construct created by locking the screws into the plate. The LPS Proximal Tibia Plate — Low Bend is part of the locking plate system (LPS), which merges locking screw technology with conventional plating techniques. The locking plate system (LPS) here has Combi-holes in the plate shaft. The Combi-hole provides flexibility of axial compression and locking capability throughout the length of the plate shaft. Indication for fractures of the proximal tibia, including: simple, comminuted, lateral wedge, depression, medial wedge, bicondylar combination of lateral wedge and depression, periprosthetic, and fractures with associated shaft fractures. The plates can also be used for treatment of nonunions, malunions, and osteopenic bone. All plates are made from medical grade stainless steel & titanium alloy.

STAINLESS STEEL LOCKING STRAIGHT SECURE PLATE

Jindal Medi Surge is a CE and ISO Certified Leading Manufacturer, Exporter of Surgical and Orthopedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum & Carbon Fiber Only. Our products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.

For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Branded & also Manufacture on an OEM basis for various international brands.

STAINLESS STEEL GUIDE WIRE

Jindal Medi Surge ("JMS" Trade Mark) is a CE, ISO13485, ISO9001 and Indian FDA Certified leading Manufacturer and Exporter of Surgical and Orthopedic / Orthopaedic Instruments in Business and Industrial Healthcare range, used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. 

The Locking Distal Femur Plate (Right/Left Leg, SS316L) is a specialized orthopedic implant designed for the fixation of distal femur fractures. Its anatomically contoured design and locking screw system ensure robust stabilization, making it ideal for comminuted, osteoporotic, or complex fractures. Manufactured from SS316L (Surgical Stainless Steel 316L), it offers exceptional strength, durability, and biocompatibility.
Key Features1. Material: SS316LSurgical Stainless Steel 316L: Resistant to corrosion and wear, ensuring long-term durability and biocompatibility.Reliable and Affordable: An economical yet high-performing implant material.2. Locking Compression Plate (LCP) SystemDual Screw Compatibility:4.5mm Cortical Screws: Allow for dynamic compression and conventional fixation.5.0mm Locking Screws: Provide angular stability, particularly beneficial in osteoporotic or comminuted bone.Locking Mechanism: Ensures enhanced stability by reducing dependence on bone-plate interface and minimizing screw loosening.3. Anatomical DesignRight/Left-Specific Contouring: Pre-contoured to match the natural anatomy of the distal femur, ensuring precise fit and alignment.Low-Profile Design: Minimizes irritation to surrounding soft tissue and reduces postoperative complications.4. ApplicationsUsed for fracture fixation in:Distal femur, including periarticular fractures.Comminuted, intra-articular, and extra-articular fractures.Suitable for:Osteoporotic fractures.Fracture nonunion or malunion.Corrective osteotomies.5. AdvantagesEnhanced Stability: The locking screw system provides robust fixation, even in poor-quality bone.Optimized Fracture Healing: Combines angular stability with compression, promoting proper bone alignment and healing.Custom Fit: Right/Left-specific plates ensure minimal intraoperative bending and adjustment.Durability: SS316L material offers resistance to mechanical stresses and corrosion.Soft Tissue Friendly: Smooth, low-profile edges reduce the risk of soft tissue irritation.6. ThicknessThe 4.5/5.0mm thickness provides optimal strength for load-bearing regions while maintaining a slim profile.Available SizesPlates are available in various lengths and configurations to accommodate different anatomical needs and fracture patterns.Would you like further information on surgical techniques, screw compatibility, or preferred manufacturers?

The Orthopedic Locking Proximal Radial Head Neck Plate 2.7mm Left/Right SS316L is a specialized implant designed for the treatment of fractures and deformities in the radial head and neck region. Below are its detailed features and applications:
Material: SS316LStainless Steel 316L (SS316L):A medical-grade, low-carbon stainless steel known for its biocompatibility.Offers excellent resistance to corrosion and mechanical durability.Commonly used in orthopedic implants for long-term performance and safety.Design FeaturesAnatomical Contouring:
Precisely contoured to fit the proximal radial head and neck.Reduces the need for intraoperative plate bending, ensuring an accurate fit and faster surgery.Left/Right-Specific Plates:
Separate designs for left and right anatomy provide a tailored fit.Ensures proper alignment and support for the specific side of the body.2.7mm Screw Compatibility:
Compatible with 2.7mm locking and cortical screws.Accommodates locking screws for stable fixation and cortical screws for added compression when needed.Low-Profile Construction:
Designed to minimize soft tissue irritation and interference with joint movement.Especially important in areas with delicate structures like the elbow joint.Locking Plate TechnologyLocking Mechanism:
Locking holes allow screws to securely engage with the plate, preventing loosening.Ideal for providing stability in osteoporotic or weakened bone.Hybrid Compatibility:
Allows the use of locking screws for rigid fixation and cortical screws for compression.Enhances surgical flexibility depending on the fracture pattern and bone quality.ApplicationsIndicated for:
Fractures of the radial head and neck.Comminuted or displaced fractures of the radial neck.Nonunion or malunion cases requiring corrective osteotomy.Trauma requiring stabilization of intra-articular and extra-articular fractures.Reconstruction:
Useful in reconstructive surgery following excision or deformity of the radial head and neck.AdvantagesStability and Rigidity:
Locking screws provide a stable construct, reducing the risk of implant failure.Promotes effective bone healing with minimal micro-motion.Durable Material:
SS316L ensures longevity and resistance to biomechanical stress and corrosion.Precise Fit:
Anatomically contoured design improves alignment and reduces surgical time.Low-profile design minimizes complications like irritation or interference with surrounding tissues.Versatility:
Hybrid screw options allow for customized fixation strategies tailored to the specific fracture.If you would like further details about its dimensions, surgical techniques, or sterilization procedures, feel free to ask!

Fessa Tube 6mm Dia. x 100mm Length

Jindal Medi Surge is a CE and ISO Certified Leading Manufacturer, Exporter of Surgical and Orthopedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum & Carbon Fiber Only. Our products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.
For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Branded & also Manufacture on an OEM basis for various international brands.

Fessa Tube 8mm Dia. x 150mm Length


Jindal Medi Surge is a CE and ISO Certified Leading Manufacturer, Exporter of Surgical and Orthopedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum & Carbon Fiber Only. Our products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.
For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Branded & also Manufacture on an OEM basis for various international brands.

Stainless Steel Small Ke Clamp

Jindal Medi Surge is a CE and ISO Certified leading Manufacturer and Exporter of Surgical and Orthopedic / Orthopaedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum, Titanium & Carbon Fiber Only. Our Products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.

For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Brand & also Manufacture on OEM basis for various international brands.

A cannulated countersink is an orthopedic surgical instrument designed to prepare bone for the insertion of screws or other implants. The "Q. C. Dia. 6.0 mm" specification indicates a quick connect (Q.C.) mechanism with a 6.0 mm diameter.
Cannulated Countersink SpecificationsDiameter: 6.0 mmDesign: Cannulated, meaning it has a hollow center.Mechanism: Quick connect (Q.C.), allowing for rapid attachment and detachment from surgical drills or handles.Uses in Orthopedic SurgeryScrew Preparation: A countersink is used to create a recess around a hole to ensure that the head of a screw sits flush with or below the surface of the bone.Bone Preparation: Helps in preparing the bone to accommodate various implants, providing a smoother interface between the implant and bone.Reduction of Stress Risers: By creating a conical recess, it reduces stress risers around the screw hole, minimizing the risk of bone fracture around the implant site.Key FeaturesPrecision: Allows for precise preparation of the bone to ensure optimal fit and alignment of screws and implants.Cannulated Design: The hollow center allows it to be used over a guide wire, ensuring accurate placement.Quick Connect Mechanism: Facilitates easy and quick changes of instruments during surgery, enhancing surgical efficiency.Material: Typically made from high-quality stainless steel or other biocompatible materials, ensuring durability and resistance to corrosion.Handling and SterilizationHandling: Requires careful handling to maintain the integrity and sharpness of the cutting edges.Sterilization: Must be sterilized before use, commonly through autoclaving, to ensure it is free of contaminants.Example ProcedureIn a typical procedure where a cannulated countersink is used:
Drilling: A hole is first drilled into the bone at the desired location for screw insertion.Guide Wire Placement: A guide wire is inserted through the drilled hole.Countersinking: The cannulated countersink is placed over the guide wire and used to create a conical recess around the hole.Screw Insertion: A screw is inserted into the prepared hole, with its head sitting flush with the bone surface.In summary, a cannulated countersink with a 6.0 mm diameter and quick connect mechanism is an essential instrument in orthopedic surgeries, providing precision and efficiency in preparing bone for screw and implant insertion.

Charnley's compression clamp is an essential instrument used in orthopedic surgery, particularly in procedures involving the knee. This instrument is designed to provide stable and precise compression during bone fixation, ensuring proper alignment and stabilization of the bones.
Overview of Charnley's Compression ClampDesign and Construction:
Material: Typically made from high-quality stainless steel to ensure durability, corrosion resistance, and ease of sterilization.Structure: The clamp features two opposing arms with serrated jaws that can securely grip the bone or implant. The arms are connected via a central screw mechanism that allows for fine adjustment of the compression force.Functionality:
Compression: The primary function of the clamp is to apply controlled compression to bone fragments or implants, facilitating proper alignment and stabilization during healing.Adjustability: The central screw mechanism allows the surgeon to adjust the amount of compression precisely, ensuring optimal fixation without over-compressing the bone.Applications in Knee Surgery:
Fracture Fixation: Used to stabilize fractures in the knee region, such as distal femur fractures or tibial plateau fractures.Osteotomy: Assists in maintaining bone alignment during corrective osteotomy procedures.Arthrodesis: Useful in knee arthrodesis (fusion) procedures where bones need to be held in close apposition for fusion to occur.Steps for Using Charnley's Compression Clamp in Knee SurgeryPreparation: Sterilize the instrument thoroughly before use. Ensure that all components are functioning properly.Positioning: Position the clamp so that the jaws are aligned with the bone fragments or implant that need to be compressed.Application: Gradually tighten the central screw mechanism to bring the jaws together, applying the desired amount of compression to the bone or implant.Stabilization: Once the desired compression is achieved, stabilize the bone or implant with additional fixation devices such as screws or plates.Release: Carefully release the clamp after fixation is secured, ensuring that the bone or implant remains in the correct position.Advantages of Using Charnley's Compression ClampPrecision: Allows for precise control of compression, reducing the risk of over-compression or insufficient fixation.Stability: Provides stable and reliable fixation during surgery, improving surgical outcomes.Versatility: Can be used in various types of knee surgeries, including fracture fixation, osteotomies, and arthrodesis.ConclusionCharnley's compression clamp is a valuable tool in the arsenal of orthopedic surgeons, particularly for procedures involving the knee. Its ability to provide controlled and precise compression makes it indispensable for achieving successful surgical outcomes in complex knee surgeries. If you require more detailed information, specific models, or purchasing options for this instrument, please let me know!

Open Small Single Pin Clamp 4.0 x 2.5mm Orthopedic Tubular External Fixator The external fixator is one of the mainstays of operative fracture treatment. It allows "local damage control" for fractures with severe soft-tissue injuries and can be used for definitive treatment of many fractures as it provides relative stability, which results in healing by callus formation. External fixation is an essential part of damage control surgery in polytrauma as it permits rapid stabilization of fractures with minimal additional (surgical) injury. Deformity correction and bone transport are also possible with external fixation. There are various methods of internal fixation for the treatment of fractures, but at certain times it is inappropriate to perform internal fixation as primary treatment. External fixation has Less damage to the blood supply of the bone, Minimal interference with soft-tissue cover, Rapid application in an emergency situation, Stabilization of open and contaminated fractures, Fracture reduction and stable fixation adjustable without surgery, Good solution in situations with high risk of infection or established infection; less experience and surgical skill required than for standard ORIF, Bone transport and deformity correction possible. All Fixators are made from Medical Grade Stainless Steel & Titanium Alloy.

Small Single Pin Clamp 4.0 - 2.5mm Orthopedic Tubular External Fixator The external fixator is one of the mainstays of operative fracture treatment. It allows "local damage control" for fractures with severe soft-tissue injuries and can be used for definitive treatment of many fractures as it provides relative stability, which results in healing by callus formation. External fixation is an essential part of damage control surgery in polytrauma as it permits rapid stabilization of fractures with minimal additional (surgical) injury. Deformity correction and bone transport are also possible with external fixation. There are various methods of internal fixation for the treatment of fractures, but at certain times it is inappropriate to perform internal fixation as primary treatment. External fixation has Less damage to the blood supply of the bone, Minimal interference with soft-tissue cover, Rapid application in an emergency situation, Stabilization of open and contaminated fractures, Fracture reduction and stable fixation adjustable without surgery, Good solution in situations with high risk of infection or established infection; less experience and surgical skill required than for standard ORIF, Bone transport and deformity correction possible. All Fixators are made from Medical Grade Stainless Steel & Titanium Alloy.

Curved Reconstruction Plate 3.5mm Orthopedic Implant The Large Fragment Plating System from Jindal Medi Surge offers the advantages of plating with the flexibility and benefits of traditional plating in one system. Offering non-locking screw options, the system can provide a construct that resists angular (eg varus, valus, torsional and axial) collapse while simultaneously acting as an effective aid to fracture reduction. A simple and straight forward instrument set features standardized drill bits and color-coded instrumentation, making it efficient and easy to use. All orthopedic large fragment plates are made from medical grade stainless steel & titanium.

Titanium DCP Plate For 3.5mm Orthopedic Implant Jindal Medi Surge Small Fragment Plates are Designed to treat the most common small bone fractures, as well as, to serve as the fastener (screw) and instrument hub for the anatomic specific implant sets. It Reflects the varied functional requirements of our customers by providing one case to contain the entire system or separate implant and instrument cases. Three dimensional graphics for rapid implant and instrument identification enhancing both surgical and processing efficiencies. Innovative “flip” tray contains screw instruments that can be placed on the mayo stand permitting rapid transition between the various screw types. All orthopedic small fragment bone plate are made from medical grade stainless steel & titanium raw-material (sterile & non sterile)

Titanium Curved Reconstruction Plate 3.5mm Orthopedic Implant Jindal Medi Surge Small Fragment Plates are Designed to treat the most common small bone fractures, as well as, to serve as the fastener (screw) and instrument hub for the anatomic specific implant sets. It Reflects the varied functional requirements of our customers by providing one case to contain the entire system or separate implant and instrument cases. Three dimensional graphics for rapid implant and instrument identification enhancing both surgical and processing efficiencies. Innovative “flip” tray contains screw instruments that can be placed on the mayo stand permitting rapid transition between the various screw types. All orthopedic small fragment bone plate are made from medical grade stainless steel & titanium raw-material (sterile & non sterile)

BROAD DCP PLATE ORTHOPEDIC IMPLANT The Large Fragment Plating System from Jindal Medi Surge offers the advantages of plating with the flexibility and benefits of traditional plating in one system. Offering non-locking screw options, the system can provide a construct that resists angular (eg varus, valus, torsional and axial) collapse while simultaneously acting as an effective aid to fracture reduction. A simple and straight forward instrument set features standardized drill bits and color-coded instrumentation, making it efficient and easy to use. All orthopedic large fragment plates are made from medical grade stainless steel & titanium.

VATERINARY MINI SINGLE KE CLAMP 


Jindal Medi Surge is a CE and ISO Certified leading Manufacturer and Exporter of Surgical and Orthopedic / Orthopaedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum, Titanium & Carbon Fiber Only. Our Products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.

For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Brand & also Manufacture on OEM basis for various international brands.

Dhs/Dcs Screw Stainless Steel

4168.050 Length 50mm4168.055 Length 55mm4168.060 Length 60mm4168.065 Length 65mm4168.070 Length 70mm4168.075 Length 75mm4168.080 Length 80mm4168.085 Length 85mm4168.090 Length 90mm4168.095 Length 95mm4168.100 Length 100mm4168.105 Length 105mm4168.110 Length 110mm4168.115 Length 115mm4168.120 Length 120mm4168.125 Length 125mm4168.130 Length 130mm4168.135 Length 135mm4168.140 Length 140mm4168.145 Length 145mmJindal Medi Surge is a CE and ISO Certified Leading Manufacturer, Exporter of Surgical and Orthopedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum & Carbon Fiber Only. Our products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.

For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Branded & also Manufacture on an OEM basis for various international brands.

A titanium clip-on self-holding clamp for an orthopedic external fixator is a specialized component designed to facilitate the assembly and adjustment of external fixator frames. These clamps are known for their ease of use, durability, and ability to maintain position without continuous manual support during the surgical procedure.
Features of a Titanium Clip-On Self-Holding Clamp:Material: Made from titanium for its strength, biocompatibility, and corrosion resistance.Clip-On Mechanism: Allows for quick attachment and detachment from the rods.Self-Holding: The clamp stays in place without requiring continuous manual support.Adjustment Screws: Used to fine-tune the positioning and secure the rods.Tube Holders: Designed to securely hold rods of specific diameters (e.g., 8mm, 11mm).Steps for Using a Titanium Clip-On Self-Holding Clamp in an External Fixator:Preoperative Planning:
Assess the fracture or deformity using imaging techniques.Plan the placement of rings and rods to ensure optimal stability and alignment.Ring and Rod Placement:
Sterilize and drape the patient properly.Position the rings around the limb at appropriate locations, ensuring strategic placement above and below the fracture or deformity.Wire or Pin Insertion:
Make small incisions at planned insertion sites.Insert wires or pins through the bone and secure them to the rings using tensioners for wires or other securing mechanisms.Attachment of Titanium Clip-On Self-Holding Clamps:
Select the appropriate clamp size for the rods being used (e.g., 8mm, 11mm).Clip the clamp onto the rods at the desired locations, ensuring the self-holding mechanism engages.Inserting and Securing Rods:
Guide the rods through the holders in the clamps.Partially tighten the adjustment screws to hold the rods in place while allowing for further adjustments.Adjusting the Clamp Position:
Fine-tune the alignment and position of the rods using the adjustment screws.Ensure the rods are correctly positioned to provide the desired stabilization and alignment of the fracture or deformity.Final Tightening:
Once the desired position and alignment are achieved, fully tighten the adjustment screws to secure the rods in place.Check the stability of the entire construct to ensure that all components are tightly fastened.Postoperative Care:
Schedule regular follow-ups to monitor healing and make necessary adjustments.Clean pin sites regularly to prevent infection.Adjust the fixator as needed for progressive correction in cases of deformity.Safety Considerations:Avoid placing wires or pins near joints or major blood vessels.Monitor pin sites regularly for signs of infection.Ensure all components, including the titanium clip-on self-holding clamps, are securely fastened to prevent loosening.Example Setup Using Titanium Clip-On Self-Holding Clamps:Select Appropriate Clamps:
Choose titanium clip-on self-holding clamps compatible with the rods used in your external fixator system (e.g., 8mm, 11mm).Attach Clamps to Rods:
Position the clamps on the rods and engage the clip-on mechanism to hold them in place.Insert and Secure Rods:
Guide the rods through the holders in the clamps.Adjust the position to ensure proper alignment and stabilization.Final Adjustments and Tightening:
Fine-tune the alignment using the adjustment screws on the clamps.Once satisfied with the positioning, fully tighten the screws to secure the rods in place.Illustrative Steps:Prepare the Limb:
Ensure the limb is properly positioned and prepared for surgery.Position the Ring and Rods:
Place the rings and rods around the limb at the appropriate locations.Attach the Titanium Clip-On Self-Holding Clamp:
Secure the titanium clip-on self-holding clamp to the rods.Insert the Rods:
Guide the rods through the clamp’s holders.Adjust and Tighten:
Use the adjustment screws to position the rods correctly and then tighten to secure.

Front Threaded Pin Schanz Screw Self Drilling Tappered Point SS316L4211SD.001 4,0 x 100mm4211SD.002 4,0 x 125mm4211SD.003 4,0 x 150mm4211SD.004 5,0 x 125mm4211SD.005 5,0 x 150mm4211SD.006 5,0 x 175mm4211SD.007 5,0 x 200mm
A Front Threaded Pin Schanz Screw with a self-drilling tapered point made from SS316L is designed for ease of use and secure fixation in orthopedic procedures. Here are the detailed specifications and features of such a surgical implant:
Specifications:Material:
SS316L: High-quality surgical-grade stainless steel known for its excellent corrosion resistance, biocompatibility, and mechanical strength.Dimensions:
Diameter: Common sizes include 3mm, 4mm, 5mm, 6mm, 8mm, and 10mm.Length: Ranges from 50mm to 200mm, depending on the application and bone size.Thread:
Type: Front-threaded (partially threaded at the distal end).Pitch: Designed to provide optimal grip and minimal insertion torque.Thread Length: Typically 10mm to 30mm, depending on the total length of the screw.Tip:
Type: Tapered, self-drilling and self-tapping for easier insertion without pre-drilling.Point: Tapered point designed to penetrate bone efficiently while minimizing trauma.Surface Finish:
Polished or passivated surface to enhance corrosion resistance and minimize tissue irritation.Sterilization:
Pre-sterilized: Typically provided in a sterile package.Autoclavable: Can be re-sterilized if needed.Compatibility:
External Fixators: Designed to be used with various external fixator systems.Clamp Compatibility: Suitable for use with standard Schanz screw clamps.Features:Biocompatibility:
SS316L is highly biocompatible, reducing the risk of adverse reactions in patients.Corrosion Resistance:
Excellent resistance to bodily fluids and cleaning agents, ensuring longevity and reliability.Strength and Stability:
High tensile strength provides robust fixation, essential for maintaining stability during bone healing.Ease of Use:
Self-drilling and self-tapping features make the insertion process quicker and easier, reducing operative time.Tapered point design facilitates smooth penetration and minimizes bone trauma.Versatility:
Available in multiple sizes to accommodate different bones and fracture types.Example Applications:Fracture Fixation:
Used in external fixator systems to stabilize bone fractures, particularly in long bones like the femur, tibia, and humerus.Deformity Correction:
Employed in corrective procedures where gradual adjustment of bone position is required.Limb Lengthening:
Used in distraction osteogenesis procedures to gradually lengthen bones.Example Set Contents:Schanz Screws:
Diameters: 3mm, 4mm, 5mm, 6mm, 8mm, 10mm.Lengths: 50mm, 75mm, 100mm, 125mm, 150mm, 200mm.Quantity: 10 each size.Insertion Tools:
T-handles or driver handles specific for Schanz screws.Sterilization Tray:
Custom tray to hold and sterilize all screws and insertion tools.Usage Instructions:Ensure proper pre-operative planning, including imaging to determine the optimal size and placement of Schanz screws.Use the appropriate insertion tools to achieve accurate and stable placement.Follow standard sterilization protocols if re-sterilization is required.

Components and FeaturesAdjustable Clamp:
Single Pin Clamp: Designed to hold an 11.0mm diameter pin securely, ensuring stable fixation. The clamp allows for fine adjustments to achieve the desired alignment.Threaded Part: The 7mm threaded part of the pin enables it to be securely fixed into the bone, providing additional stability.Fixed Vice:
Fixed Design: Unlike open vices, the fixed vice offers a more rigid and stable connection, ensuring the pin remains in a fixed position once secured.Secure Locking Mechanism: Ensures the pin is locked in place, providing stability throughout the healing process.External Fixator System:
Connection Rods: Used to connect multiple clamps and vices, forming a stable external framework to support the bone during healing.Pins/Wires: Typically made from stainless steel or titanium, these pins are inserted through the skin into the bone to stabilize the fracture.ApplicationsComplex Fractures: Ideal for fractures that are too complex or severe for internal fixation.Open Fractures: Suitable for managing open fractures where internal fixation may pose a higher risk of infection.Bone Lengthening and Reconstruction: Used in procedures that involve bone lengthening or complex reconstructive surgery.AdvantagesStability: The fixed vice design offers greater stability compared to adjustable or open vices, ensuring the pin remains securely in place.Adjustability: Despite the fixed vice, the adjustable clamp allows for precise alignment and positioning of the pin.Versatility: Can be used in various types of fractures and bone conditions requiring external fixation.ConsiderationsTraining: Proper training for surgeons and surgical staff is essential for the effective use of this external fixator component.Sterilization: All components must be thoroughly sterilized before use to prevent infections and maintain surgical sterility.Patient Monitoring: Regular monitoring and adjustments may be necessary to ensure the fixator remains effective and comfortable for the patient throughout the healing process.SummaryThe Single Pin Adjustable Clamp with Fixed Vice (11.0mm diameter, 7mm threaded part) is a critical component in external fixator systems used in orthopedic surgery. Its design provides stable and secure fixation, making it suitable for complex fractures and conditions requiring external support. Proper training, sterilization, and patient monitoring are crucial for achieving successful surgical outcomes and promoting effective bone healing.
Typical Instrument Set ContentsAdjustable Clamps: Multiple clamps designed to hold 11.0mm diameter pins.Fixed Vices: Fixed vices to securely lock the pins in place.Connection Rods: Various lengths to connect the clamps and create the external framework.11.0mm Pins/Wires: Stainless steel or titanium pins with a 7mm threaded part for secure insertion into the bone.Screwdrivers and Wrenches: Tools for tightening and adjusting the clamps and rods.Drill Guides and Drill Bits: For precise placement of pins.Sterilization Tray and Containers: For organizing, sterilizing, and storing the instruments.Procedure OverviewPreparation: Ensure all instruments and pins are sterilized.Pin Insertion: Insert the 11.0mm pins with 7mm threaded parts into the bone under fluoroscopic guidance.Clamp Attachment: Secure the adjustable clamps to the pins.Vice Securing: Use the fixed vice to lock the pins in place, ensuring stability.Rod Connection: Connect the clamps using the connection rods to form the external frame.Adjustment: Adjust the clamps and rods to achieve optimal alignment and stabilization of the bone fragments.Post-Operative Care: Regularly monitor and adjust the fixator as needed during the healing process.

The Single Pin Adjustable Clamp with Open Vice (6.0mm Pin) is a specialized component used in external fixator systems for orthopedic surgery. This device is designed to stabilize bone fractures using an external framework, allowing for precise adjustments and secure fixation. Here's a detailed overview of this instrument:
Components and FeaturesAdjustable Clamp:
Single Pin Clamp: Designed to securely hold a 6.0mm pin or wire, providing stability and allowing for precise positioning of the bone fragments.Adjustability: The clamp allows for angular and positional adjustments of the pin, offering flexibility to the surgeon in aligning the bone fragments optimally.Open Vice:
Open Design: The open vice design facilitates easy access for adjustments without the need to disassemble the entire fixation device.Secure Locking Mechanism: Ensures the pin remains securely in place once positioned, maintaining stability throughout the healing process.External Fixator System:
Connection Rods: These rods connect multiple clamps and vices, forming a rigid external framework that supports the bone during healing.Pins/Wires: Stainless steel or titanium pins, typically 6.0mm in diameter, are inserted through the skin into the bone to provide stabilization.ApplicationsComplex Fractures: Used in cases where fractures are too complex or severe for internal fixation.Open Fractures: Suitable for open fractures where internal fixation might increase the risk of infection.Post-Traumatic Bone Reconstruction: Assists in the reconstruction and realignment of bone fragments after severe trauma.AdvantagesAdjustability: Provides precise positioning and alignment of bone fragments, ensuring optimal healing conditions.Accessibility: The open vice design allows for easy adjustments without extensive disassembly, improving efficiency during post-operative care.Stability: Offers a stable external framework that supports the bone during the entire healing process.ConsiderationsTraining: Proper training for surgeons and surgical staff is essential for the effective use of external fixators and the single pin adjustable clamp with open vice.Sterilization: All components must be sterilized before use to prevent infections and maintain surgical sterility.Patient Monitoring: Regular monitoring and adjustments may be necessary to ensure the fixator remains effective and comfortable for the patient.SummaryThe Single Pin Adjustable Clamp with Open Vice (6.0mm Pin) is a vital component in external fixator systems used for orthopedic surgery. Its design allows for precise adjustments and secure fixation of bone fragments, making it ideal for managing complex fractures and providing stable external support. Proper training, sterilization, and patient monitoring are crucial for achieving successful surgical outcomes and promoting effective bone healing.
Typical Instrument Set ContentsAdjustable Clamps: Multiple clamps to accommodate the required number of pins.Connection Rods: Various lengths to connect the clamps and create the external framework.6.0mm Pins/Wires: Stainless steel or titanium pins for insertion into the bone.Screwdrivers and Wrenches: Tools for tightening and adjusting the clamps and rods.Drill Guides and Drill Bits: For precise placement of pins.Sterilization Tray and Containers: For organizing, sterilizing, and storing the instruments.Procedure OverviewPreparation: Ensure all instruments and pins are sterilized.Pin Insertion: Insert the 6.0mm pins into the bone under fluoroscopic guidance.Clamp Attachment: Secure the adjustable clamps to the pins.Rod Connection: Connect the clamps using the connection rods to form the external frame.Adjustment: Adjust the clamps and rods to achieve optimal alignment and stabilization of the bone fragments.Post-Operative Care: Regularly monitor and adjust the fixator as needed during the healing process.

Hinge 90° Orthopedic External Fixator Instrument The Ilizarov apparatus is a type of external fixation used in orthopedic surgery to lengthen or reshape limb bones; as a limb-sparing technique to treat complex and/or open bone fractures; and in cases of infected nonunions of bones that are not amenable with other techniques. It is named after the orthopedic surgeon Gavriil Abramovich Ilizarov from the Soviet Union, who pioneered the technique. All orthopedic ilizarov external fixator system is made from medical grade stainless steel, aluminium & carbon fiber raw material.

Orthopedic Carbon Fiber Rods 1/8 Inches Diameter External Fixator

Orthopedic carbon fiber rods, typically used in external fixators, are slender rods made from carbon fiber composite materials. These rods are designed to provide stability and support to fractured or injured bones during the healing process. The 1/8 inch diameter rods are relatively thin, making them suitable for applications where a smaller profile is desired or where space is limited.
Carbon fiber rods offer several advantages in orthopedic applications:
Strength and Durability: Carbon fiber is renowned for its exceptional strength-to-weight ratio, making it an ideal material for supporting fractured bones without adding significant weight or bulk.
Biocompatibility: Carbon fiber is generally well-tolerated by the human body, reducing the risk of adverse reactions or complications.
Radiolucency: Carbon fiber is radiolucent, meaning it does not obstruct X-rays or other imaging modalities. This property allows healthcare professionals to monitor the healing process without interference from the fixation device.
Corrosion Resistance: Unlike metal fixators, carbon fiber rods are not susceptible to corrosion, which can extend their lifespan and reduce the risk of complications.
Customizability: Carbon fiber rods can be manufactured in various diameters and lengths to accommodate different anatomical structures and clinical requirements.
Overall, orthopedic carbon fiber rods offer a lightweight, durable, and biocompatible solution for external fixation in orthopedic surgery, promoting optimal healing and patient comfort.

SMALL CLMAP 4.0MM X 2.5MM EXTERNAL FIXATOR

Jindal Medi Surge offers the External Fixation System for the treatment of complex distal radius fractures. The External Fixator is designed to hold pins in place for fracture reduction or distraction to align the wrist and to provide ligamentotaxis to the wrist on a temporary basis while the distal radius heals. Versatility allows surgeon to gain initial reduction with the fixator in place and then separately adjust only those planes needing correction. Adjustments may be made independently for distraction, radial/ulnar deviation, flexion/extension and dorsal/palmar translation. Radiolucent body aids in surgeon visualization during fracture reduction and distraction. External Fixator is designed to be lightweight. Small Bone Fixator is an innovative solution for stabilizing fractures resulting from high-energy trauma, including fusions, osteotomies, open and/or comminuted fractures, infected nonunions, and fractures with length discrepancies. The Small Bone Fixator System is simple to use, offers versatile pin placement options and stability, and is cost-effective. All orthopedic external fixator are made from medical grade raw material.

The Open Single Pin Clamp for external fixator systems is an important component used in orthopedic surgeries to stabilize bone fragments, particularly in cases of complex fractures, deformities, and bone lengthening procedures. This type of clamp is designed to securely hold a single pin, providing stability while allowing for easy adjustments. Here’s an in-depth overview of this surgical clamp:
Components and FeaturesOpen Single Pin Clamp:
Design: Holds a single pin securely, providing flexibility and adjustability.Material: Typically made from high-strength stainless steel or titanium, ensuring durability and biocompatibility.Open Configuration: The open design allows for easy insertion and adjustment of the pin, making it user-friendly for surgeons.External Fixator System:
Rods/Struts: Connect various clamps and allow for adjustments to the position and tension, facilitating gradual correction of deformities or lengthening of the bone.Pins/Wires: Inserted percutaneously into the bone and secured by the clamps.ApplicationsComplex Fractures: Ideal for stabilizing fractures that are too severe for internal fixation.Limb Lengthening: Used in gradual distraction osteogenesis to achieve desired bone length.Deformity Correction: Correcting angular or rotational deformities in bones.Non-Union Fractures: Treating fractures that have not healed properly with other methods.Bone Transport: Moving bone segments to fill in defects caused by injury, infection, or congenital issues.AdvantagesEase of Use: The open design allows for quick and easy insertion and adjustment of pins, improving surgical efficiency.Flexibility: Allows for precise positioning and alignment of the pin, which is crucial for accurate bone stabilization.Versatility: Can be used in various locations on the external fixator system, allowing for flexible configuration based on specific surgical needs.ConsiderationsTraining: Proper training for surgeons and surgical staff is essential for the effective use of this external fixator component.Sterilization: All components must be sterilized before use to prevent infections.Patient Monitoring: Regular monitoring and adjustments may be necessary to ensure the fixator remains effective and comfortable for the patient throughout the healing process.SummaryThe Open Single Pin Clamp for external fixator systems is a crucial tool in orthopedic surgery for stabilizing complex fractures, performing bone lengthening, and correcting deformities. Its design provides enhanced flexibility and ease of use, making it a versatile and essential component in external fixation procedures.
Typical Instrument Set ContentsOpen Single Pin Clamps: Multiple clamps designed to hold single pins securely.Connecting Rods/Struts: Various lengths to connect the clamps and facilitate adjustments.Pins/Wires: Stainless steel or titanium pins for insertion into the bone.Screwdrivers and Wrenches: Tools for tightening and adjusting the clamps and rods.Drill Guides and Drill Bits: For precise placement of pins.Sterilization Trays and Containers: For organizing, sterilizing, and storing the instruments.Procedure OverviewPreparation: Ensure all instruments and pins are sterilized.Pin Insertion: Insert the pins into the bone under fluoroscopic guidance.Clamp Attachment: Secure the open single pin clamps to the pins, ensuring stability.Rod/Strut Connection: Connect the clamps using the rods or struts to form the external frame.Adjustment: Adjust the clamps and rods to achieve optimal alignment and stabilization of the bone fragments.Post-Operative Care: Regularly monitor and adjust the fixator as needed during the healing process, ensuring proper bone healing and alignment.This detailed approach ensures that the Open Single Pin Clamp provides the necessary stability, precision, and flexibility required for effective external fixation in orthopedic procedures.

Components and FeaturesAdjustable Clamp:
Single Pin Clamp: Designed to securely hold a 6.5mm pin, providing stability and allowing for precise positioning of bone fragments.Threaded Part: The 7mm threaded part ensures the clamp can be securely fixed to the bone, offering additional stability.Fixed Vice:
Fixed Design: Offers a rigid and stable connection, ensuring the pin remains in a fixed position once secured.Secure Locking Mechanism: Ensures the pin is locked in place, providing stability throughout the healing process.External Fixator System:
Connection Rods: Used to connect multiple clamps and vices, forming a stable external framework to support the bone during healing.Pins/Wires: Typically made from stainless steel or titanium, these 6.5mm pins are inserted through the skin into the bone to stabilize the fracture.ApplicationsComplex Fractures: Ideal for fractures that are too complex or severe for internal fixation.Open Fractures: Suitable for managing open fractures where internal fixation may pose a higher risk of infection.Bone Lengthening and Reconstruction: Used in procedures that involve bone lengthening or complex reconstructive surgery.AdvantagesStability: The fixed vice design offers greater stability compared to adjustable or open vices, ensuring the pin remains securely in place.Adjustability: Despite the fixed vice, the adjustable clamp allows for precise alignment and positioning of the pin.Versatility: Can be used in various types of fractures and bone conditions requiring external fixation.ConsiderationsTraining: Proper training for surgeons and surgical staff is essential for the effective use of this external fixator component.Sterilization: All components must be thoroughly sterilized before use to prevent infections and maintain surgical sterility.Patient Monitoring: Regular monitoring and adjustments may be necessary to ensure the fixator remains effective and comfortable for the patient throughout the healing process.SummaryThe Single Pin Adjustable Clamp with Fixed Vice (11.0mm diameter, 7mm threaded part) for 6.5mm pins is a crucial component in external fixator systems used in orthopedic surgery. Its design provides stable and secure fixation, making it suitable for complex fractures and conditions requiring external support. Proper training, sterilization, and patient monitoring are essential for achieving successful surgical outcomes and promoting effective bone healing.
Typical Instrument Set ContentsAdjustable Clamps: Multiple clamps designed to hold 6.5mm diameter pins.Fixed Vices: Fixed vices to securely lock the pins in place.Connection Rods: Various lengths to connect the clamps and create the external framework.6.5mm Pins/Wires: Stainless steel or titanium pins for insertion into the bone.Screwdrivers and Wrenches: Tools for tightening and adjusting the clamps and rods.Drill Guides and Drill Bits: For precise placement of pins.Sterilization Tray and Containers: For organizing, sterilizing, and storing the instruments.Procedure OverviewPreparation: Ensure all instruments and pins are sterilized.Pin Insertion: Insert the 6.5mm pins with 7mm threaded parts into the bone under fluoroscopic guidance.Clamp Attachment: Secure the adjustable clamps to the pins.Vice Securing: Use the fixed vice to lock the pins in place, ensuring stability.Rod Connection: Connect the clamps using the connection rods to form the external frame.Adjustment: Adjust the clamps and rods to achieve optimal alignment and stabilization of the bone fragments.Post-Operative Care: Regularly monitor and adjust the fixator as needed during the healing process.

Fessa Tube 6mm Dia. X 30mm Length

Jindal Medi Surge is a CE and ISO Certified Leading Manufacturer, Exporter of Surgical and Orthopedic Instruments used for Human (Adult and Pediatric) and Veterinary Surgical Procedures. All Products are made from Surgical Grade Stainless Steel, Aluminum & Carbon Fiber Only. Our products are used by Government Institutes, Private Hospitals, Small Clinics, Individual Doctors Worldwide.
For Bulk Order & Customized Listing, kindly message us.
We sell exclusively on our JMS Branded & also Manufacture on an OEM basis for various international brands.

The Orthopedic DHS/DCS Screw with a 12.5mm diameter, featuring a Compression Screw, made of SS316L, is a specialized surgical implant used in conjunction with DHS (Dynamic Hip Screw) or DCS (Dynamic Condylar Screw) plates for the fixation of femoral fractures. Below is a detailed description of its features and uses:
Key SpecificationsDesign:
Screw Type:Lag screw design for insertion into the femoral head or condyles.Provides stability and compression at the fracture site.Diameter: 12.5mm, optimized for secure fixation in the femur.Thread:Large cancellous threads for better grip in trabecular bone.Smooth shaft near the proximal end to facilitate controlled sliding and dynamic compression.Compression Screw:An additional component used to tighten the lag screw within the barrel of the DHS or DCS plate, achieving precise and stable fracture compression.Material:
SS316L (Surgical Stainless Steel 316L):Biocompatible and corrosion-resistant.Provides durability and long-term stability within the body.Length Variations:
Available in multiple lengths to accommodate different patient anatomies and fracture configurations.ApplicationsFracture Fixation:
Proximal femoral fractures:Intertrochanteric fractures (with DHS plate).Femoral neck fractures.Distal femoral fractures:Supracondylar fractures (with DCS plate).Dynamic Stabilization:
Works in conjunction with DHS/DCS plates to allow controlled sliding and compression at the fracture site.Features & BenefitsDynamic Compression:
The compression screw ensures stable fixation and precise fracture alignment.Promotes healing by providing controlled load-sharing across the fracture.Secure Fixation:
Large cancellous threads improve purchase in spongy bone, minimizing the risk of screw loosening.Smooth Sliding Mechanism:
The lag screw's design enables dynamic movement within the plate barrel, allowing controlled compression during weight-bearing.Durability and Biocompatibility:
SS316L ensures resistance to wear and corrosion, suitable for long-term implantation.Versatility:
Compatible with both DHS and DCS systems, making it suitable for a wide range of femoral fractures.AdvantagesEnables precise and stable compression, reducing the risk of non-union or malunion.Dynamic sliding mechanism allows for natural fracture healing under mechanical stress.Adaptable for both proximal and distal femoral fractures.Selection ConsiderationsPreoperative Planning:Choose the appropriate screw length based on fracture location and patient anatomy.Compatible Plates:Ensure the DHS or DCS plate selected is compatible with the 12.5mm lag screw.Surgical Expertise:Proper placement and compression adjustment are critical for optimal outcomes.Let me know if you need further details on screw lengths, surgical techniques, or compatible plate options!
DHS/DCS Screw 12.5mm With Compression Screw SS316L4168.050 Length 50mm4168.055 Length 55mm4168.060 Length 60mm4168.065 Length 65mm4168.070 Length 70mm4168.075 Length 75mm4168.080 Length 80mm4168.085 Length 85mm4168.090 Length 90mm4168.095 Length 95mm4168.100 Length 100mm4168.105 Length 105mm4168.110 Length 110mm4168.115 Length 115mm4168.120 Length 120mm4168.125 Length 125mm4168.130 Length 130mm4168.135 Length 135mm4168.140 Length 140mm4168.145 Length 145mm